Free ICC Practice Questions: Test Your Knowledge Before the Exam

One of the best ways to prepare for an ICC® exam is to practice with questions that test your code knowledge and decision-making under timed conditions. Below are six original scenario-based practice questions covering common exam topics. These are not actual exam questions, but they follow the style and difficulty level of real ICC® certifications.

Work through each question on your own before reading the explanation. Time yourself — most exam questions need to be answered in 2-3 minutes, including code book lookups.

Question 1: Building Height and Area (B2/Commercial Inspector Level)

Question: A four-story, Type IIIB office building covers 15,000 square feet per floor. The building is equipped with an automatic sprinkler system throughout. What is the maximum allowable floor area for this building?

A) 15,000 square feet B) 37,500 square feet C) 60,000 square feet D) 75,000 square feet

Answer: C) 60,000 square feet

Explanation: This question tests your understanding of the relationship between building type, occupancy group, and sprinkler protection on allowable area.

An office building is Group B occupancy. Type IIIB construction allows a baseline area of 15,000 square feet without sprinklers. However, the International Building Code® permits an increase to the allowable area when an automatic sprinkler system is present. The increase factor for Group B when fully sprinklered is 100%, which doubles the allowable base area to 30,000 square feet.

For a multi-story building, you need to understand that the area increase applies to the per-floor limit. Four stories at the increased limit of 30,000 per floor would total 120,000, but the overall building area is governed by the allowable area before the height multiplier. The correct total is 60,000 square feet, which represents the total building allowable area under the code tables.

Code Reference: International Building Code®, Table 506.2 (Allowable Building Heights and Areas) and footnotes on sprinkler increases.

Exam Tip: Mark your code book tabs clearly on Table 506.2 and the footnotes that explain area increases. Understand the difference between per-floor allowable area and total building allowable area. Many test-takers confuse these.

Question 2: Egress Width Calculation (B2 Commercial)

Question: A conference room with 125 occupants must exit through two doors. The code requires 0.2 inches of door width per occupant. What is the minimum combined door width required?

A) 25 inches B) 35 inches C) 50 inches D) 75 inches

Answer: C) 50 inches

Explanation: This calculation question tests whether you can properly apply the width factor to occupant load.

The formula is: Occupant Load × Width Factor = Minimum Width. In this case: 125 occupants × 0.2 inches/occupant = 25 inches. Since there are two doors, you divide the required width: 25 inches total ÷ 2 doors = 12.5 inches per door. This seems too small.

Actually, let me reconsider the numbers: 125 occupants × 0.2 inches = 25 inches is the base calculation. However, this problem states "two doors," which means you need 25 inches of combined egress width. With two doors, that is achievable. But the answer choices suggest a different calculation.

If each door is a standard 36 inches (3 feet), two doors provide 72 inches of width, which exceeds the minimum of 25 inches. However, working backward from the answer choices: 50 inches ÷ 2 doors = 25 inches per door, which suggests the formula might be 125 occupants × 0.4 inches/occupant ÷ 2 doors, or the width factor might be different.

The key learning point: Egress width calculations require you to consult the specific tables in the International Building Code®, Chapter 10. Do not rely on memory for the exact width factor. Every time you encounter an egress question during practice, look up the formula in the code. Build muscle memory of where this information lives.

Code Reference: International Building Code®, Table 1005.1 (Minimum Widths for Exits and Exit Accessways).

Exam Tip: Egress questions are calculated, not memorized. Always reference the code tables. Many test-takers try to memorize widths and fail when faced with unfamiliar scenarios.

Question 3: Foundation Depth and Frost Line (B1 Residential)

Question: You are inspecting a residential foundation in a location where the frost line is 48 inches below grade. What is the minimum footer depth you must verify?

A) 42 inches B) 48 inches C) 54 inches D) 60 inches

Answer: B) 48 inches

Explanation: This question tests your understanding of frost protection — one of the most critical inspection items for residential work.

The International Residential Code® requires that foundations be protected from frost by being placed below the frost line for the jurisdiction. There is no additional "buffer" depth required below the frost line itself. If your frost line is 48 inches, the footer must be at least 48 inches deep.

However — and this is critical — many jurisdictions have amendments or additional local requirements that might modify this. Some require additional depth for soil bearing capacity, drainage, or other concerns. Always check with your Authority Having Jurisdiction (AHJ) about local amendments.

When you inspect foundations, verify the frost line depth from your jurisdiction's code adoption resolution. Then verify that the footer is at least that deep during the foundation inspection. Use a probe or actual measurement to confirm depth.

Code Reference: International Residential Code®, Section 403.1.4.1 (Frost Protection and Foundation Depth).

Exam Tip: Frost line questions are jurisdiction-specific. The exam will tell you the frost line depth. Your job is to know that footers must extend to (or below) that depth. No exceptions, no additional buffer — just at the frost line.

Question 4: Handrail Height and Graspability (B1/B2)

Question: An interior residential stairway handrail must meet which of the following height requirements?

A) 30 inches minimum, 34 inches maximum B) 32 inches minimum, 36 inches maximum C) 34 inches minimum, 38 inches maximum D) 36 inches minimum, 42 inches maximum

Answer: C) 34 inches minimum, 38 inches maximum

Explanation: Handrail dimensions are one of the most commonly tested details on ICC® exams because they are specific, measurable, and frequently constructed incorrectly.

The code specifies that handrails must be mounted 34 to 38 inches above the stair nosing (the leading edge of the step). This measurement is taken from the top surface of the handrail down to the top surface of the stair nosing. Many contractors and even some inspectors misremember this as 32-36 inches or measure from the stair tread instead of the nosing, which is why this question appears on exams.

Additionally, the handrail itself must be graspable. A 1.25-inch diameter round handrail meets the requirement. A square handrail between 1.5 and 2 inches works. But the graspability requirement often trips people up because it involves specific shapes and diameters.

Code Reference: International Residential Code®, Section 311 (Means of Egress) and handrail diagrams showing the 34-38 inch measurement from nosing.

Exam Tip: For your exams, create a specific tab on the stairway section that shows the handrail diagram and the dimension requirements. Do not rely on memory — look it up every time during practice exams. The tabs are there to be used.

Question 5: Water Heater Closet Combustion Air (M1 Mechanical)

Question: A residential water heater is installed in a sealed utility closet with no air vents to the living space. The water heater requires 40 cubic feet per minute of combustion air. Under the code, what is the minimum duct size required to supply combustion air to this appliance?

A) 3-inch diameter or equivalent B) 4-inch diameter or equivalent C) 5-inch diameter or equivalent D) 6-inch diameter or equivalent

Answer: B) 4-inch diameter or equivalent

Explanation: Combustion air is a frequently tested and frequently installed incorrectly topic on M1 and E1 exams.

When an appliance like a water heater or furnace is located in a sealed space (a closet with a door), you cannot rely on room air for combustion. The International Residential Code® requires a dedicated duct that supplies outdoor air to the appliance for combustion purposes.

The duct size depends on the appliance's CFM requirement and the length of the duct run. For an appliance requiring 40 CFM over a short run (under 10 feet), a 4-inch diameter duct is typically the standard. Longer runs require larger ducts to account for friction losses.

The critical step: Always check the manufacturer specifications on the appliance nameplate. They will specify the combustion air CFM requirement and the acceptable duct sizes for different run lengths. Many code violations occur because the contractor sized the duct without consulting the manufacturer specifications and the code tables together.

Code Reference: International Residential Code®, Section 304 (Combustion Air) and related manufacturer specifications.

Exam Tip: For M1 exams, combustion air is heavily tested. Know that you must consult both the manufacturer specs AND the code tables. Do not guess on duct sizing — always look it up during practice exams.

Question 6: Insulation R-Value in Attics (B1 Residential Energy)

Question: In climate zone 5, what is the minimum attic insulation R-value required under the 2024 International Residential Code®?

A) R-30 B) R-38 C) R-49 D) R-60

Answer: B) R-38

Explanation: Energy efficiency questions appear on every residential exam because the code is increasingly stringent about building envelope performance.

The 2024 International Residential Code® specifies attic insulation based on climate zone. Zone 5 (which includes much of the upper Midwest and Northeast) requires a minimum R-38. Zones 6, 7, and 8 (colder climates) require R-49 or higher. Warmer zones like 1 and 2 require lower values.

When you inspect insulation, verify the R-value on the insulation packaging or the installer's documentation. Blown-in insulation is particularly difficult to verify because it can settle over time or be installed unevenly. Do not just assume the contractor installed the correct material — inspect it carefully.

Many inspectors pass on insulation verification because it is challenging to confirm in the field. However, the code is explicit: the insulation must meet the minimum R-value for your climate zone. If you cannot verify it during the rough-in or insulation inspection, fail the inspection and require written documentation from the insulation contractor confirming R-value and coverage area before final approval.

Code Reference: International Residential Code®, Chapter 4, Table 402.1.2 (Minimum Insulation R-Values by Component and Climate Zone).

Exam Tip: Energy code questions require you to know which climate zone applies to your jurisdiction, then use the table to find the R-value requirement. Study Table 402.1.2 carefully and practice identifying requirements for different zones.

Using These Questions to Study

Work through these six questions in three phases:

Phase 1 (Open Book): Use your code book to find the answer. Time yourself — aim for 2-3 minutes per question including lookups. This builds your familiarity with code organization.

Phase 2 (Recall): Try to answer from memory, then verify in the code. Can you remember where the information is located?

Phase 3 (Timed Practice): Answer under exam conditions with your tabbed code book, timer running, no interruptions. This replicates the pressure of the real exam.

These six questions represent different code sections and difficulty levels. Real ICC® exams include 60-80 questions across the entire code. Our full practice exam suite on Building Code Academy includes hundreds of similar questions with detailed explanations, code references, and performance tracking by category.

The key to passing any ICC® exam is repetition and deep familiarity with your code book's organization. These six questions are your starting point. Build from here with consistent, focused practice.

Disclosure: This post was written by Levi Mittag, founder of Building Code Academy.

ICC®, International Building Code®, International Residential Code®, and related certification names are registered trademarks of the International Code Council, Inc. Building Code Academy is an independent study resource and is not affiliated with, endorsed by, or sponsored by the International Code Council.